当前位置： 首页 > 标准详情页

IEC 60071-1 Ed. 8.0现行

Insulation co-ordination Part 1: Definitions, principles and rules

出版：International Electrotechnical Committee

获取原文如何获取原文？问客服获取原文，即可享受本标准状态变更提醒服务！

专家解读视频

基本信息

标准编号： IEC 60071-1 Ed. 8.0

发布时间：2006/1/23 0:00:00

标准类别：Standard

出版单位：International Electrotechnical Committee

标准页数：35

标准简介

IEC 60071-1:2006 applies to three-phase a.c. systems having a highest voltage for equipment above 1 kV. It specifies the procedure for the selection of the rated withstand voltages for the phase-to-earth, phase-to-phase and longitudinal insulation of the equipment and the installations of these systems. It also gives the lists of the standard withstand voltages from which the rated withstand voltages should be selected. This standard recommends that the selected withstand voltages should be associated with the highest voltage for equipment. This association is for insulation co-ordination purposes only. The requirements for human safety are not covered by this standard. Although the principles of this standard also apply to transmission line insulation, the values of their withstand voltages may be different from the standard rated withstand voltages. The apparatus committees are responsible for specifying the rated withstand voltages and the test procedures suitable for the relevant equipment taking into consideration the recommendations of this standard. NOTE: In IEC 60071-2, Application Guide, all rules for insulation co ordination given in this standard are justified in detail, in particular the association of the standard rated withstand voltages with the highest voltage for equipment. When more than one set of standard rated withstand voltages is associated with the same highest voltage for equipment, guidance is provided for the selection of the most suitable set. The main changes from the previous edition are as follows: - in the definitions (3.26, 3.28 and 3.29) and in the environmental conditions (5.9) taken into account clarification of the atmospheric and altitude corrections involved in the insulation co-ordination process; - in the list of standard rated short-duration power frequency withstand voltages reported in 5.6 addition of 115 kV; - in the list of standard rated impulse withstand voltages reported in 5.7, addition of 200 kV and 380 kV; - in the standard insulation levels for range I (1kV < Um ≤ 245 kV) (Table 2) addition of the highest voltage for equipment Um = 100 kV; - in the standard insulation levels for range II (Um ≤ 245 kV) (Table 3) replacement of 525 kV by 550 kV and of 765 kV by 800 kV; - in order to remove that part in the next revision of IEC 60071-2, addition of Annex A dealing with clearances in air to assure a specified impulse withstand voltage in installation; - in Annex B, limitation at two Um values for the values of rated insulation levels for 1kV < Um ≤ 245 kV for highest voltages for equipment Um not standardized by IEC based on current practice in some countries. It has the status of a horizontal standard in accordance with IEC Guide 108<

本标准替代的旧标准

IEC 60071-1 Ed. 7.0

替代本标准的新标准

IEC 60071-1 Ed. 8.1

等同采用的国际标准

VDE 0111-1:2006 - Identical

BS EN 60071-1:2006+A1:2010 - Identical

PN EN 60071-1:2008 - Identical

OVE/ONORM EN 60071-1:2007 - Identical

PN EN 60071-1:2006 - Identical

NEN EN IEC 60071-1:2006 - Identical

DIN EN 60071-1 (2006-11) - Identical